There are currently no product reviews.
This is an excellent handbook. We had no information on the appliance until we obtained this and are now able to use the appliance to its full potential. Strongly recommended.
Very happy to find this from owners-manual.com and the enclosed spec sheet as well.
Not longer available from Sony.
The Owner's manual was very helpful. The WEGA is about 35 years old and needed repair.
Your Website is pretty good und easily to handle.
Perfect. Very good service and very good scanning quality. All sheets are very legible. Thank's
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
USERâS GUIDE 2470
The operational procedures for Modules 2428 and 2470 are identical. All of the illustrations in this manual show Module 2428. â¢ Press B to change from mode to mode. Each mode is explained in detail on the following pages.
â¢ After you perform an operation in any mode, pressing B returns to the Timekeeping Mode.
Time Setting Mode
PM indicator Day of the week Day
â¢ In the Timekeeping Mode, press C to switch between the 12-hour and 24-hour formats. â¢ In the Timekeeping Mode, press A to illuminate the display for a few seconds. â¢ Day of the week is displayed as follows. SU: Sunday MO: Monday TU: Tuesday WE: Wednesday TH: Thursday F R : Friday SA: Saturday
Mode Indicator Minutes Seconds
The Stopwatch Mode lets you measure elapsed time, split times, and two finishes. The range of the stopwatch is 59 minutes, 59.99 seconds.
Split time indicator
(a) Elapsed time measurement Start Stop Re-start Stop Clear
Backlight Precautions The backlight uses an EL (electro-luminescent) panel that causes the entire display to glow for easy reading in the dark. â¢ The electro-luminescent panel that provides illumination loses power after very long use. â¢ The illumination provided by the backlight may be hard to see when viewed under direct sunlight. â¢ The watch may emit an audible sound whenever the display is illuminated. This is due to vibration of the EL panel used for illumination, and does not indicate malfunction. â¢ Frequent use of the backlight shortens the battery life.
(b) Split time measurement Start Split Split release Stop Clear
(c) Split time and 1st-2nd place times Start Split
First runner finishes.
Second runner finishes. Record time of first runner.
Record time of second runner.
Mode indicator Hour Minutes
When the Daily Alarm is switched on, the alarm sounds for 20 seconds at the preset time each day. When the Hourly Time Signal is switched on, the watch beeps every hour on the hour. To set the alarm time 1. Hold down A while in the Alarm Mode until the hour digits start to flash on the display. The hour digits flash because they are selected. 2. sequence. change the selection in the following Press A to â¢ Pressing A also illuminates the display.
Time Setting Mode
PM indicator Day of the week Day
To set the time and date 1. Use B to enter the Time Setting Mode. â¢ The secondâs digits flash because they are selected. 2. Press A to change the selection in the following sequence. â¢ Pressing A also illuminates the display.
Seconds Day of week Hour Day Minutes Month
Hourly time signal on indicator
Alarm on indicator
Normal Alarm Mode (No digit flashes)
â¢ Once you reach the normal Alarm Mode, you have to hold down A again until the hour digits start to flash. 3. Press C to increase the selected digits. Holding down C changes the number at high speed. â¢ The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping. â¢ When setting the alarm time using the 12-hour format, take care to set the time correctly as morning or afternoon (PM). 4. After you set the alarm time, press A to return to the Alarm Mode. At this time the Daily Alarm is switched on automatically. To stop the alarm Press A to stop the alarm after it starts to sound. To switch the Daily Alarm and Hourly Time Signal on and off Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly Time Signal in the following sequence.
[Alarm on Indicator/Hourly Time Signal on Indicator]
3. While the secondâs digits are selected (flashing), press C to reset the seconds to â00â. If you press C while the secondâs count is in the range of 30 to 59, the seconds are reset to â00â and 1 is added to the minutes. If the secondâs count is in the range of 00 to 29, the minuteâs count is unchanged. 4. While any other digits (besides seconds) are selected (flashing), press C to increase the number. While the day of the week is selected, pressing C advances to the next day. Holding down C changes the current selection at high speed. 5. After you set the time and date, press B to return to the Timekeeping Mode. â¢ If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Timekeeping Mode automatically.
Daily Alarm only
Hourly Time Signal only
To test the alarm Hold down C while in the Alarm Mode to sound the alarm.