There are currently no product reviews.
Excellent service from this company (including a total refund on an earlier purchase when through no fault of the company the manual was incomplete). I have purchased several manuals which I have been very satisfied with, as I am with this one. Highly recommended.
It was easy to order and received exactly what I needed. Only complaint would be the 24 hours you have to wait.
Manual was delivered in a timely manner and was all in English as advertised. The manuals I received when we moved into our flat were in German, Italian, and French. Having never used a steamer before, and not speaking/reading German very well, I needed an English Manual. this was a huge help.
Great Manual. This manual is available no where else. It was exactly what I was looking for. Only in German.
This GRUNDIG UV5A Owner Manual is not only an instruction manual but a total functional circuit description of the Multimeter and includes circuit diagram at the end pages. It is very helpful for repairing and calibrating the instrument. It is written in two languages English and German for international support. It was very easy to repair my unit with this document. Regards, Regis Pauly, Electrical Engineer.
Operation Guide 2711/4327
*The configuration of your watch may differ somewhat from that shown in the illustration. Minute hand
To set the time
1. Pull out the crown to the second click. â€¢ This causes the second hand to stop. 2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the time you want to set, and then back it up to the proper setting. 3. Push the crown back in to the normal position to restart timekeeping.
24-hour hand First click (Day setting)
Second click (Time setting) Stopwatch minute hand Day Second hand Stopwatch second hand Crown (Normal position)
To set the day
1. Pull out the crown to the first click. 2. Set the day by rotating the crown. 3. Push the crown back in to the normal position. â€¢ Avoid setting the day between 9:00 p.m. and 1:00 a.m. (the day display may not change in the following day).
Using the Stopwatch
The stopwatch lets you measure elapsed time up to 59 minutes, 59 seconds. You can also correct the position of the stopwatch second hand when necessary. â€¢ The illustration shows a time of 20 minutes, 40 seconds. â€¢ Do not try to perform stopwatch operations while the crown is pulled out either to the first or second click. If you try to press a button, you might accidentally cause the crown to rotate and change the current time or day setting.
To measure elapsed time
1. Press A to start the stopwatch. 2. Press A to stop the stopwatch. â€¢ You can resume the measurement operation by pressing A again. 3. Press B to reset the stopwatch.
Adjusting the Stopwatch Second and Minute Hand Positions
Use of the stopwatch can cause the starting positions of the stopwatch minute hand and second hand to become misaligned. Use the following procedures to check hand alignment and to adjust the positions of the hands so they point to 12 oâ€™clock when the stopwatch is reset.
To adjust the positions of the stopwatch hands
1. Press B to reset the stopwatch, and check the alignment of the stopwatch minute hand and second hand. 2. Pull out the crown to the second click. 3. Press A to move the stopwatch second hand forward until it points to 12 oâ€™clock. 4. If the stopwatch minute hand is aligned correctly, proceed to step 5. If the stopwatch minute hand is also misaligned, press B so the stopwatch minute hand jumps to 0. 5. After making the adjustments you want, push the crown back in to its normal position. â€¢ Note that pulling the crown out also stops the timekeeping second hand. After performing the above procedure, you should also adjust the timekeeping setting.
Elapsed time bezel
â€¢ Some water resistant models are equipped with a screw lock crown. â€¢ With such models, you must unscrew the crown in the direction noted in the illustration to loosen it before you can pull it out. Do not pull too forcibly on such crowns. â€¢ Also note that such watches are not water resistant while their crowns are loosened. Be sure to screw the crowns back in as far as they will go after making any setting.
I For watch with the elapsed time bezel Rotate the elapsed time bezel to align the mark with the minute hand. After certain amount of time elapsed, read the graduation on the elapsed time bezel which the minute hand points to. The elapsed time is indicated.
5 0 4