There are currently no product reviews.
ThankΒ΄s for your help, I already recived these manual from you
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
3. Press C to show the barometric pressure calibration display. At this time, âOFFâ or the barometric pressure value should be flashing on the display. â¢ The âOFFâ indicator appears when the factory setting is being used for the calibration. 4. Each press of D increases the displayed barometric pressure by 1 hPa/ mb, while pressing B decreases it. Holding down either button changes the value at high speed. â¢ Pressing B and D at the same time returns to the âOFFâ display. 5. After calibrating the barometric pressure, press A to return to the Barometric Pressure/Temperature Display. â¢ If you do not operate any button for a few minutes while the barometric pressure digits are flashing, the flashing stops and the watch goes back to the Barometric Pressure/Temperature Display.
4. After calibrating the temperature, press A to return to the Barometric Pressure/Temperature Display. â¢ If you do not operate any button for a few minutes while the temperature digits are flashing, the flashing stops and the watch goes back to the Barometric Pressure/Temperature Display.
A built-in altimeter uses a pressure sensor to detect the current air pressure, which is then used to estimate the current altitude in accordance with ISA (International Standard Atmosphere) values for altitude and air pressure. If you preset a reference altitude, the watch will also calculate the current relative altitude based on your preset value. Altimeter functions also include data storage memory and an altitude alarm. Important! â¢ This watch estimates altitude based on air pressure. This means that altitude readings for the same location may vary if air pressure changes. â¢ Sudden changes in the weather make it impossible to produce accurate altitude readings. â¢ This watch employs a semiconductor pressure sensor, which is affected by temperature changes. When taking altitude measurements, be sure to do so while ensuring that the watch is not exposed to temperature changes. â¢ Do not use this watch while participating in sports where there are sudden altitude changes. Also, do not use this watch for applications that demand professional or industrial level precision. This watch should not be used while engaging in the following activities: sky diving, hang gliding, paragliding, gyrocopter riding, glider riding, etc.
A built-in temperature sensor measures temperature and shows the measured value on the display. The thermometer can be calibrated. Important! Temperature measurements are affected by your body temperature (while you are wearing the watch), direct sunlight, and moisture. To achieve a more accurate temperature measurement, remove the watch from your wrist, place it in a well ventilated location out of direct sunlight, and wipe off all moisture from the case. It takes approximately 20 to 30 minutes for the case of the watch to reach the actual surrounding temperature.
About temperature measurements
Temperature measurements are taken automatically every five minutes, regardless of what mode the watch is in. Measured temperature values can be viewed in the Timekeeping or Altimeter Modes. Temperature measurements are taken every five seconds for the first three minutes after you display the Timekeeping Modeâs Barometric Pressure/Temperature display, or after you enter the Altimeter Mode. After that, temperature measurements are taken every five minutes. â¢ Temperature measurement data can be recalled along with altitude measurement data.
When no reference altitude is preset:
â¢ The watch produces approximate altitude readings.
When a reference altitude is preset:
â¢ Before beginning the climb, set the reference altitude to 0 m at the foot of the mountain. This makes it possible to determine the difference in altitude between the reference point and your destination. â¢ To determine the height of a tall building, set the reference altitude to 0 m on the ground floor. Note, however, that if the building is pressurized or air conditioned, you may not be able to get a good reading. â¢ To determine the difference in altitude between your house and another location, set the reference altitude to 0 m at your house, and then check the reading when you arrive at the other location. â¢ When mountain climbing, you can input the altitude from a marker as your reference altitude, which will then let you know your altitude as your climb proceeds. The following conditions will prevent you from obtaining accurate readings:
Understanding the temperature display
1. Use C to enter the Timekeeping Mode. 2. Press D to display the Barometric Pressure/Temperature Display.
( Barometric Pressure/Temperature Display ) â¢ The display shows ââ â.â Â°Câ if a measured value falls outside the range of â20.0Â°C to 60.0Â°C. The normal display will return as soon as the temperature returns within the allowable range. â¢ For details on viewing the temperature in the Altimeter Mode, see Understanding the altimeter display.
When air pressure changes because of changes in the weather Extreme temperature changes When the watch itself is subjected to strong impact
Calibrating the temperature measurement
The temperature sensor of this watch is calibrated at the factory before shipment and further adjustment is normally not required. If noticeable error is found in the temperature readings produced by the watch, you can adjust it to correct the error. Important! Incorrectly calibrating the temperature measurement of this watch can result in incorrect readings. Carefully read the following before doing anything. â¢ Compare the readings produced by the watch with those of another reliable, accurate thermometer. â¢ If adjustment is required, remove the watch from your wrist and wait for 20 or 30 minutes to give the temperature of the watch time to stabilize.
About altitude measurements
There are two types of altitude measurements: those for displayed data (Altimeter Mode measurement) and those for memory data (memory measurements; See Memory measurements).
Altimeter Mode measurement
This type of measurement is performed only when the watch is in the Altimeter Mode. As soon as you enter the Altimeter Mode, measurements are taken every five seconds for the first three minutes. After that, measurements are taken every two minutes. The display unit for Altimeter Mode measurements is 5 m, and the display range is 0 to 6000 m. â¢ The measured altitude may be a negative value in cases where there is a reference altitude value set or because of certain atmospheric conditions.
To calibrate the temperature
1. In the Timekeeping Mode, use D to display the barometric pressure and temperature. 2. Hold down A until the display clears. âOFFâ or the temperature value should be flashing on the display. â¢ The âOFFâ indicator appears when the factory setting is being used for the calibration.
3. Each press of D increases the displayed temperature by 0.1Â°C while pressing B decreases it. Holding down either button changes the value at high speed. â¢ Pressing B and D at the same time returns to the âOFFâ display.