There are currently no product reviews.
as a first-time user and buyer from this site, i found the overall service outstanding!! this product is a godsend as, without it, i would never have been able to find my way around and use my machine as intended. i will certainly use this site again as required. many many thanx!!
This manual is exactly what I needed. This site always has every manual I need, and it is also much less expensive then most other sites. This is the only manual site I will use.
Useful manual, good scan, worth the pay if you find the unit difficult to operate.
Exactly as described, the full user-manual (145 pages). Perfect.
USERâS GUIDE 2424
â¢ Press B to change from mode to mode.
Timekeeping Mode Press . Alarm Mode Stopwatch Mode
To turn the Daily Alarm and Hourly Time Signal on and off Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly Time Signal in the following sequence.
Daily Alarm only
Hourly Time Signal only
To test the alarm Hold down C while in the Alarm Mode to sound the alarm.
Month - Day Day of week
1/100 second Mode indicator
DST on indicator
Hour : Minutes
The Stopwatch Mode lets you measure elapsed time, split times, and two finishes. The range of the stopwatch is 23 hours 59 minutes, 59.99 seconds. â¢ If you do not operate any button for a few minutes while the all-zero screen is on the display in the Stopwatch Mode, the watch goes back to the Timekeeping Mode automatically.
â¢ In the Timekeeping Mode, press C to switch between the 12-hour and 24hour format. â¢ When the 12-hour format is selected, âp.m.â times are indicated on the display by P, while âa.m.â times are indicated by A. No indicators are used with the 24-hour format. To set the time and date 1. Hold down A until the secondâs digits start to flash. 2. Press B to move the selection around the display in the following sequence.
Seconds Day Month DST on/off Year Hour Minutes
(a) Elapsed time measurement Start Stop Re-start Stop Clear
(b) Split time measurement
3. While the secondâs digits are selected (flashing), press C to reset them to 00. If you press C while the secondâs count is in the range of 30 to 59, they are reset to 00 and 1 is added to the minutes. If the secondâs count is in the range of 00 to 29, the minuteâs count is unchanged. 4. While the DSTâ setting is selected (DST on indicator is flashing), press C to toggle it on (on) and off (OF). 5. While any other setting (besides seconds) is selected (flashing), press C to change it. Holding down C changes the digits at high speed. â¢ The date can be set with the range of January 1, 2000 to December 31, 2039. 6. After you set the time and date, press A to return to the Timekeeping Mode. â¢ If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Timekeeping Mode automatically. â¢ The watchâs built-in full automatically set in automatically makes date. â¢ The day of the week is automatic calendar accordance with the allowances for different month lengths and leap years. Once you set the date, there should be no reason to change it except after the replacement of the watchâs battery. â Daylight Saving Time (DST), which is also sometimes called âsummer timeâ advances the time for one hour, as is the custom in some areas during the summer. Remember that not all countries or even local areas use Daylight Saving Time.
(c) Split time and 1st-2nd place times Start Split
First runner finishes.
Second runner finishes. Record time of first runner.
Record time of second runner.
About the Auto-Start function With the Auto-Start function, the watch performs a 5-second countdown. When the countdown reaches zero, stopwatch operation starts automatically. During the final three seconds of the countdown, a beeper sounds with each second.
To turn the Auto-Start function on and off
While the display is showing all zeros in the Stopwatch Mode, press A to toggle it on and off.
About the Multi Illuminator Backlight
â¢ In any mode, press L to illuminate the display for about 3 seconds. â¢ The backlight of this watch employs a âMulti Illuminatorâ light, which illuminates the display using one of three colors. â¢ The color of the backlight changes according to function. â¢ Frequent use of the backlight shortens the battery life. â¢ The illumination provided by the backlight may be hard to see when viewed under direct sunlight. â¢ The backlight automatically turns off whenever an alarm sounds.
Auto start OFF Auto start ON
AUTO START indicator
â¢ To stop the Auto-Start countdown and return to the all-zero display, press A. â¢ Pressing C while the Auto-Start countdown is in progress immediately starts the stopwatch.
Hour : Minutes Mode indicator
When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the preset time each day. When the Hourly Time Signal is turned on, the watch beeps every hour on the hour. â¢ If you do not operate any button for a few minutes while in the Alarm Mode, the watch goes back to the Timekeeping Mode automatically. To set the alarm time 1. Hold down A until the hour digits start to flash on the display. The hour digits flash because they are selected. At this time the Alarm is automatically turned on. 2. Press B to change the selection in the following sequence.
Alarm on indicator
Hourly time signal on indicator
3. Press C to increase the number. Holding down C changes the digits at high speed. â¢ The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping. â¢ When setting the alarm time using the 12-hour format, take care to set the time correctly as morning or afternoon. 4. After you set the alarm time, press A to return to the Alarm Mode. â¢ If you do not operate any button for a few minutes while a selection is flashing, the flashing stops and the watch goes back to the Alarm Mode automatically. To stop the alarm â¢ Press any button to stop the alarm after it starts to sound.