There are currently no product reviews.
What can i say but i would have been lost without your support.
TrΓ¨s satisfait ! envoi rapide, Grand catalogue disponible. Many thanks !
Delivery came quite promptly and in a very readable format. Thank you.
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
USERâS GUIDE 2737/2738
World Time digitally displays the current time in 27 cities (29 time zones) around the world. â All of the operations in this section are performed in the World Time Mode, which you enter by pressing C.
4. Press A to exit the setting screen. â You can also perform steps 1 and 2 of the above procedure whenever you need to view the current auto-repeat and progress beeper settings.
Current time for the selected city code
To view the time in another city In the World Time Mode, press D to scroll eastwardly through city codes. â The city code is displayed for about one second, and then it is replaced with the current time for that city code. â For full information about city codes, see the âCity Code Tableâ. â If the current time shown for a city is wrong, it probably means there is a problem with your Timekeeping Mode time and/or Home City code settings. Go to the Timekeeping Mode and make the necessary adjustments.
To use the countdown timer Press D while in the Countdown Timer Mode to start the countdown timer. â The countdown timer operation continues even if you exit the Countdown Timer Mode. â Press D while a countdown operation is in progress to pause it. Press D again to resume the countdown. â To completely stop a countdown operation, first pause it (by pressing D), and then press A. This returns the countdown time to its starting value.
The stopwatch lets you measure elapsed time, split times, and two finishes. â The display range of the stopwatch is 59 minutes, 59.99 seconds. â The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. â The stopwatch measurement operation continues even if you exit the Stopwatch Mode. â Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement. â All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C.
To toggle a city code time between Standard Time and Daylight Saving Time 1. In the World Time Mode, use D to display the city code whose Standard Time/Daylight Saving Time setting you want to change. 2. Hold down A for about two seconds to toggle between Daylight Saving Time (DST displayed) and Standard Time (DST not displayed). â The DST indicator is on the display whenever you display a city code for which Daylight Saving Time is turned on. â The Module 2738 DST indicator is displayed as .
â Note that the DST/Standard Time setting affects only the currently displayed city code. Other city codes are not affected. â Note that you cannot switch between Standard Time and Daylight Saving Time while GMT is selected as the city code.
Minutes Seconds 1/100 second
To measure times with the stopwach
The countdown timer can be set within a range of one minute to 60 minutes. An alarm sounds when the countdown reaches zero. The countdown timer also has an auto-repeat feature and a progress beeper that signals the progress of the countdown. â All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C.
Start Split Time Start Two Finishes Start
Configuring the Countdown Timer
The following are the settings you should configure before actually using the countdown timer. Countdown start time; Auto-repeat on/off; Progress beeper on/off â See âTo configure the countdown timerâ for information about setting up the timer.
First runner finishes. Display time of first runner.
Second runner finishes.
Display time of second runner.
Alarm time (Hour : Minutes) Alarm number
Auto-repeat When auto-repeat is turned on, the countdown automatically restarts from the countdown start time when it reaches zero. If left running, the countdown is repeated a total of eight times, after which it stops automatically. When auto-repeat is turned off, the countdown stops when it reaches zero and the display shows the original countdown start time. â Pressing D while an auto-repeat countdown is in progress pauses the current countdown. You can resume the auto-repeat countdown by pressing D, or you can press A to reset to the countdown time starting value. Countdown Timer Beeper Operations The watch beeps at various times during a countdown so you can keep informed about the countdown status without looking at the display. The following describes the types of beeper operations the watch performs during a countdown. Countdown End Beeper The countdown end beeper lets you know when the countdown reaches zero. â When the progress beeper is turned off, the countdown end beeper sounds for about 10 seconds, or until you press any button to stop it. â When the progress beeper is turned on, the countdown end beeper sounds for about one second. Progress Beeper When the progress beeper is turned on, the watch uses beeps to signal countdown progress as described below. â Starting from five minutes before the end of the countdown, the watch emits four short beeps at the top of each countdown minute. â 30 seconds before the end of the countdown, the watch emits four short beeps. â The watch emits a short beep for each of the last 10 seconds of the countdown. â If the countdown start time is six minutes or greater, the watch emits a short beep for each second of the final 10 seconds before the five-minute point is reached. Four short beeps are emitted to signal when the five-minute point is reached.
You can set five independent Daily Alarms. When an alarm is turned on, the alarm tone sounds when the alarm time is reached. One of the alarms is a snooze alarm, while the other four are one-time alarms. You can turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour. â There are six screens in the Alarm Mode. Four are for one-time alarms (indicated by numbers from AL1through AL4), one is for a snooze alarm (indicated by SNZ), and one is for the Hourly Time Signal (indicated by SIG). â All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm screens until the one whose time you want to set is displayed.
To configure the countdown timer 1. While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the current countdown start time starts to flash, which indicates the setting screen. â If the countdown start time is not displayed, use the procedure under âTo use the countdown timerâ to display it. 2. Press C to move the flashing in the sequence shown below to select other settings.
Start Time Auto-repeat
â To set a one-time alarm, display one of the screens indicated by an alarm number from AL1through AL4. To set the snooze alarm, display the screen indicated by SNZ. â The snooze alarm repeats every five minutes. 2. After you select an alarm, hold down A until the hour setting of the alarm time starts to flash, which indicates the setting screen. â This operation automatically turns on the alarm. 3. Press C to move the flashing between the hour and minute settings. 4. While a setting is flashing, use D (+) and B (â) to change it. â When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no indicator) or p.m. (P indicator). 5. Press A to exit the setting screen.
3. When the setting you want to change is flashing, use B and D to change it as described below.
Setting Start Time Auto-repeat Progress Beeper Screen Button Operation Use D (+) and B (â) to change the setting. â You can set a start time in the range of 1 to 60 minutes in 1-minute increments. Press D to toggle auto-repeat on ( displayed) and off ( displayed). Press D to toggle the progress beeper on (ON) and off (OF).